iFlight TITAN Chimera7 LR 320mm SucceX-D F7 V2.1 50A BL_32 ESC 6S 7 Inch Long Range FPV Racing Drone BNF w/ 2806.5 1300KV Motor Caddx Polar Vista Digital System
- Stock: In Stock
- Model: 1749131
- SKU: 1749131
Notice: becuase DJI Air Unit has been stopped produced, this item will comes with Caddx Polar Vista Digital System.
July 5th, 2021.
Notice: Get notification from iFlight, All of their flight controllers come without Barometer.
Oct. 26th,2021.
Click here buy 2806.5 1800KV Speed Cruiser Motor Version
Click here buy Analog Version.
Introduction:
iFlight 7 inch Long-Range Drone that can carry bigger batteries to get the flight time to surf the swiss alps if you want!
Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control.
Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising.
GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included).
Vertical and horizontal TBS CRSF antenna mounts included to cover you and your antenna dead ends.
Features:
- 6mm rigid arm design for more stiffness
- Top- and bottom battery mount option
- XING 2806.5 efficient wide stator motors
- GPS pre-installed for more safety at distance
- TPU Bottom Stand for Gopro Camera (Camera and Camera Mount are NOT included)
- 360° TPU protection, DJI cam protection and antenna mounts
- DJI FPV Air Unit, buttery-smooth 720p120fps FPV feed (TPU soft mounted)
- No props in view (DJI Air unit record in 1080p/60fps)
- Battery voltage LED status light (illuminated IF logo on the bottom)
Specification:
Brand Name: iFlight
Model: Chimera7
Item Name: 320mm F7 6S 7 Inch Long Range FPV Racing Drone
Drone Wheelbase: 320mm
Optional Receiver Version: BNF-DJI ( Built-in DJI Receiver)
TBS CRSF Nano RX ( Built-in DJI Receiver & External TBS CRSF Nano Receiver)
Weight: 628.1 ( without Battery)
Flight Time: 17-19 Mins ( Take Example as 6S 4500mAh Lipo)
| Chimera7 320mm Frame Kit | Wheelbase: 320mm Main body dimension: 258*199mm Bottom to top distance: 20mm Arm thickness: 6mm Bottom plate thickness: 3mm Top plate thickness: 2mm Upper(middle) plate thickness: 3mm Camera plate thickness: 3mm (included TPU inserts) |
| SucceX-D F7 V2.1 TwinG Flight Controller | MCU: 216MHz STM32F722 Gyroscope: 2x ICM20689 Barometer: NO Blackbox: 32MB Betaflight OSD: YES BEC: 5V 2.5A / 9V 2.5A Current sensor scale: 100 Inverter for SBUS input (UART2-RX) Smartaudio & Tramp VTX protocol supported Beeper pad: Yes RSSI input pad: No UARTs: 5 Motor outputs: 8 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5) 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V) BLHeli32 Telemetry：RX5 Input voltage: recommended 2-6S, MAX 8S Firmware Target: IFLIGHT_F722_TWING Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm Dimensions: 36x36mm Weight: 7.5g USB type-C |
| SucceX 50A BLHeli_32 4in1 ESC | MCU: STM32F051 Up tp 48kHz PWM frequency Capacitance: 470uF/50V Current Sensor: Yes Input: 2-6S LIPO Constant: 50A / Burst: 60A BlHeli32 telemetry: Yes BEC: No Supports up to Dshot1200, Proshot, Multishot Target: iFlight-BL32-4IN1 Weight: 14.4g Size: 43x39mm (including the power pads) Mounting Hole: 30.5x30.5mm/Φ3mm |
| XING 2806.5 1300KV Motor | Voltage: 2-6S KV: 1300KV Configuration: 12N14P Bearing: NMB 11*5*5 Stator Diameter: 28 Stator Length: 6.5mm Shaft Diameter: M5 No.of Cells(Lipo): 2-6S Weight: 49.5g(with a short cable) Motor mount hole: 19x19 φ3mm |
| Gemfan 7040 3-Blade Propeller | Quantity: 2 CW & 2 CCW Color may vary |
| Optional Receiver Version | BNF-DJI Version: Built-in Vista Receiver ( On Caddx Polar Air Unit Module); this version is compatible with DJI Remote Controller. TBS CRSF Nano RX Version: Built-in DJI Receiver and has a external TBS CRSF Nano RX; this version is compatible with DJI Remote Controller and Official TBS Radio Transmitter |
| Lipo Battery ( NOT Included) | Recommend 5S 3000mAh above (slow cruising) or 6S 2500mAh above |
Package Included:
1x Chimera7 Drone
1x TPU bottom stand incl. lock screw ( for Installing TPU Camera Mount)
1x Caddx Polar Air Unit ( Built Well on Drone)
1x 5.8G Albatross RP-SMA Antenna LHCP 150mm
2x Gemfan 7040 Propeller CW
2x Gemfan 7040 Propeller CCW
4x 20x250mm PU Leather Battery Strap (Color May Vary)
